How to share a Project

When asking for help on the forums, it is hard to make any definite suggestions without having sight of the Schematic or PCB in question.

In EasyEDA it is possible to post a link to a public copy of your project or to share it privately.

To share a Project publically, go to:

Home > My Account > Project

https://easyeda.com/projects/mylists

and click on the 'No Entry' sign under the megaphone symbol:

Then right-click on the Project name and copy the link.

To share a Project privately, right-click on the Project name in the left hand Navigation panel of an Editor window:

and share it with Support at EasyEDA.com

#Skill#
Circuit Design
Can EasyEDA fabricate this? Rectangular cutouts

I plan on having EasyEDA fabricate this board when I'm done designing it. After looking through a couple of other posts about rectangular pads I'm still not confident that I did it correctly and that EasyEDA can do this.

You can see my project here (I've made it public now): https://easyeda.com/TyeEasyEDA/Boomerang_Keyboard-a2d4e41a4fbf4da490f883c4b93fd55c

There are 48 rectangular cutouts that I need to insert tiny programmable SK2812 LEDs in to. Each cutout also has 4 pads around it to solder-glob the LED into place.

Did I represent this cutout correctly? Can EasyEDA make this as shown on the board? (or is there a more correct way?)

Thank you.

#PCB#
Circuit Design
Bug Reports
Can't switch a project from private to public

BUG

Concise problem statement: It's not possible to switch a project from private to public anymore

Steps to reproduce bug:

  1. Right-click on a project

Results: there is no "Modify" choice (unlike what is described on https://easyeda.com/Doc/Tutorial/share.htm)

Expected results: there should be a Modify choice from which the user can switch from private to public (or the documentation to do this should be updated if the right procedure is different)

Browser: Chrome 54.

#Bug Reports#
Bug Reports
Advice On Schematic/Simulation Results

Hey Guys,
I've just started using easy eda. Which seems to be a great web app. I'll start by saying I'm relatively new to schematic/spice pcb apps as well as electronics in general so I apologize in advance!

I've got an issue with simulation which I was hoping someone might be kind enough to offer some advice or look at schematic and tell me where I've gone wrong. I'm sure there is probably a simple (embarrassingly so) problem to fix.

But I've tired working it out with no luck.

The schematic I'm trying to built is a RIAA phono inverting op amp based on the phonocube. I've built it on a breadboard (albeit with different op amp I think it was opa2134) and it worked fine.

Here is links hopefuly I've shared it correctly?

https://easyeda.com/editor#id=ab054771c95447e8b56925dc7ed7b079

https://easyeda.com/editor#id=ab054771c95447e8b56925dc7ed7b079

https://easyeda.com/normal/Zero_Impedance_Phono-ab054771c95447e8b56925dc7ed7b079

I've got a couple of issues/questions.

  1. I'm trying to simulate the frequency response based off a 1v/1k sine. The simulation based of selecting octave 100 increments 20hz to 20k runs fine without error but the graph FR results don't make sense? If I place a probe before op amp and RIAA curve I get a flat response which is as expected but when I put a probe after the 3.3uf output cap which is post RIAA compensation it seems I'm getting a result the exact opposite of what I'm expecting. Given that the RIAA pre emphasis sees a 20db cut at low end, 0db at 1khz and boost in high end I would expect that the response based of 1khz generator would see the bass 20+db 0 at 1khz and cuts to the highs, but this isn't the case. The FR response is cut in low end and boosted in highs. Does this make sense?
    I'm not sure what I'm missing here or what I've done wrong but it ain't what I expected to see.

Any advice would be appreciated.

  1. The simulation seems to be running ok but I'm not sure if I have connected/setup dual rail power supply corrrectly?

And lastly.

I've had a look at details on the different type of simulations you can run but I can't work out what test and parameters I need to use to test gain of circuit? I want to provide a 0.4mv signal and test voltage at output. What test/parameters should I use?

Any help would be greatly appreciated, I'm new to electronics so my apologies again if I've asked some dumb questions!!!

Thanks heaps guys! I would really appreciate some help.

#Simulation#
Circuit Design
Select & delete on visible layer also selects & deletes on invisible layers

BUG

Concise problem statement:

Investigating:

https://easyeda.com/forum/topic/Spurious_tracks_in_DRV8825_stepper_motor_driver_carrier_package_causing_DRC_errors-MKDxPvpHZ

has shown that if a right or left drag is used to select the tracks on the bottom solder layer with the All layers and Top silkscreen visibility turned off (i.e. All layers and Top silkscreen invisible) then when the selected content on the bottom solder layer is deleted and the All layers and Top silkscreen visibility turned on again; all the pads and some of the silkscreen text has also been deleted.

Steps to reproduce bug:

  1. Open DRV8825 Stepper Motor Driver Carrier package for editing;

  2. Set the All layers and Top silkscreen visibility OFF;

  3. Set active layer to bottom solder layer;

  4. Use right or left hand drag to select all + crossed traces on bottom solder layer;

  5. Press Delete key (deletes all + crossed traces on visible bottom solder layer);

  6. Set the All layers and Top silkscreen visibility OFF;

Results:

All pads and - depending on extent of drag select rectangle - some or all silkscreen text and possibly the outline as well are deleted.

Expected results:

Expect that only selected content on Visible layer should be deleted.

In fact probably expect that only selected content on Active and Visible layers should be deleted.

Browser:

Chrome

#Bug Reports#
Bug Reports