Hi,
In EasyEDA Pro, when having a copper region in the PCB with "Optimization" property set to "Yes", generating a PDF will not have the copper plane correctly printed.
Here is a screenshot, in the PDF there is void between the copper region and the silkscreen yellow rectangle:

With copper region with "Optimization" set to No, there is no issue, the PDF match the EasyEDA PCB view.
Here is an example project: https://oshwlab.com/amubtdx/test_pcb_pdf_export_copper_region
Here is the full exported PCB PDF page:

My EasyEDA Pro version is:
Version : V2.1.49.1.de255bc8.674264
BuiltDate : 2024-02-19
I have very little idea what I'm doing, this is the first PCB I have tried to route
https://easyeda.com/editor#id=66b8c85af07f4692a35f1eda57a2a01f
I want to connect the GND pins of the ESP32-S3 to the ground plane & also the ground pins of the encoders & Microbus header. How do I do that?
#PCB#Just want to thank you guys for listening to all the requests and creating such a well thought out feature, it works perfectly and the manual is easy to understand.
For any users reading this I am talking about EasyEDA pro's reuse layout feature. If you have the same circuit many times in your schematic you can just layout on the PCB side one time now!
entrance:Top menu - Layout - Reuse layout routing
or you can find it under group if you right click.
Instructions can be found: https://prodocs.easyeda.com/en/pcb/layout-group/index.html
under the multipex layout section
#PCB#(“Version : V2.1.49.573a4102.674264 BuiltDate : 2024-01-30”)
I am having difficulty with EasyEDA-PRO in Half Offline mode. Hoping that someone will point out with what settings I need to correct, or if you are seeing the same issues.
The planned PCB is a 2 layer board.
In particular the DRC is detecting spacing failures after autorouting (internal EasyEDA, or Freerouting), even with what I think the correct parameters have been applied. Should the autorouting layout not provide appropriate spacing between traces, vias, pads etc, or do I need to move stuff by hand afterwards? I realize I will need to re-route certain traces etc, however has anyone seen similar results like what I am seeing below? Thanks.
[I was also getting DRC spacing errors for pad spacing on a Micro-USB connector (C2972784), however that error has somehow disappeared today... with no apparant changes applied to the settings]
Here is an example with results of Freerouting autorouter (similar results for EasyEDA autorouter):

You can see from the above, that vias are placed too close to trace, traces routed too close to component pads or slots.
Here are the PCB layout parameters:

The following is the DRC Rules (I modified to match JLCPCB capabilities for 2 Layer PCB)
Safe Clearance Design Rules settings:

The above settings were selected based on JLCPCB Capabilities for 2 Layer PCB. See JLCPCB capabilities: https://jlcpcb.com/capabilities/pcb-capabilities
Track Physics Design Rules settings:

Via Size Physics Design Rules settings:

#PCB#
Got my first boards from jlcpcb! Super rewarding, but ready for rev2.
I got my 'rev1' version of the board that I used for prototyping, everything worked sans a few of my own screw ups (the buttons were surface mount when I meant through hole & I forgot to wire up my I2C resistors, doh!) - but I was able to test everything with some improvising and ready for a few revisions!
I included the EDA link for r2 below, things I changed were really around fixing my dohs, power distribution, and making board a bit smaller. In rev1 I also had the switch for 2 power sources (board & dedicated servo) – but for rev2 I rather have 1 power source if i can. Can I get away with powering the board + 2 servos with the 6v 3a dc power in the way I have it drawn? Would be 2 micro servos that max out at around 750ma.
For rev1 I also did 2 layer pcb with the bottom layer containing a ground plane – it was suggested prior to do 4 layer pcb, with layer 2/3 being ground planes - thoughts?
I also posted this on Reddit and got some slack for the autorouting in easyeda and was suggested I do more manual or even use vias for 5v/vcc/gnd and reserver traces for signal. Is that the way? Thank you all, apprecite the support!
PSA: I'm a novice when it comes to this – I'm a software engineer, but really love playing around with hardware, so be easy on me.
– Nick (https://www.nleby.com)
Project Link: https://oshwlab.com/nicholasleby/tc-v1-0
Some pics of the r1 board I did with easyeda and jlcpcb:


The right way to include a componenet like https://www.lcsc.com/product-detail/OLED-Displays-Modules_HS-HS96L03W2C03_C5248080.html is to include the compoenent in the schematic. However JCP says there are no male-male headers included in BOM or assembly. How can I include the headers for that so the output files (not just BOM) have it to be soldered correctly using headers?
#Schematic#









