Multiple Issues With Pro

I am having a lot of issues since moving to the Pro version of EasyEDA.

Issue 1.
    It seems to crash continously when opening projects - sometimes at 50%, sometimes at 75% (This has been mentioned by others) I think it must have crashed over 40 times for me today.

Issue 2.
    Alot of the library parts seem to be corrupt and cause faults within the schematic asking for the components to be deleted and insterted again. Sometimes this works, othertimes not. Sometimes saving the file, closing EasyEDA and opening it again and the parts are fine. Most infuriatingly though is when it is all fine, it saves, and you open it again and its complaining again!

Issue 3.
    I have had A LOT of issues with reuse blocks - I spent ages making some to make my life easier and more time efficient, and I have now spent all evening struggling to actually import any reuse blocks into my schematic (even simple ones with few components) whereby it starts to open the block - I see the loading bar flashing away as if its doing something - then after maybe 5 minutes it all jsut stops and there is no component to insert to the schematic. if I save the schematic at this point, and reopen it - sometimes the reuse block is in the tree on the left, but still not in the schematic. I have to delete it from the tree and try another 20 times and maybe then it will work.

Issue 4.
    The component search function is so bad, I have to use the LCSC website to find components and then type them in to find out if they are in stock. For example, if I want a 200Ohm resistor in a 402, in the standard version I can search 200Ohm R0402 and it find them - and it will display the resistance value against the results. I do the same on this verison and I get absolute rubbish. if I manage to get to the filter, then it seems like the filter doesnt actually update the results. There needs to be a way of filtering results properly and then organising them by what JLC actually have in stock.

I'll update this topic with some pictures if it helps, but there seems to be some thing seriously wrong with the stability of Pro at the moment.

#Bug Reports#
Bug Reports
Preventing pin and mounting holes from going all the way through the board

I'm an electronics noob so sorry if this is a dumb question.

I am designing a very simple bipolar EMG probe. It consists of three copper electrodes on the bottom, each wired to a 3.5mm headphone jack on top. I'm planning to connect it to an off-the-shelf EMG amp like the Grove EMG detector or the OYMotion Gravity EMG sensor. Here's a picture:

Screen Shot 2023-01-18 at 2.31.48 AM.png

As you can see, the headphone jack's mounting holes go all the way through the entire board including the electrodes, reducing their contact area. The headphone jack (PJ-621C) has extremely tiny pins that do not extend below the component body so I don't see why it needs to penetrate 3 whole layers of fiberglass on this 4-layer board.

Is it possible to stop drilling the holes before reaching the bottom layer? Even better, would that be possible on a 2-layer board with only a single sheet of fiberglass? I did find this post about vias that said only through-holes were supported and blind vias were not, but that was only about vias and it's a 5-year-old post.

Thank you

#PCB#
Circuit Design
Quick n00b question - using components not stocked by JLCPCB

Hi,

So I am just designing a very simple circuit board which will use these Wago connectors: https://www.wago.com/gb/pcb-terminal-blocks-and-pluggable-connectors/smd-pcb-terminal-block/p/2065-100_998-403



They are not in any of the catalogs on EasyEDA or JLCPCB.

Is there any way for JLCPCB to make a PCB with these components mounted? It isn't too much of an issue as I go through testing, but if I scale up I was wondering if JLCPCB are the right service.

#SMT#
SMT Components