AC analysis parameters for SINE source

I am quite new to EasyEDA and LTSPICE, but I have noticed something which seems like it could be a bug.

I have a small project to simulate a filter from a particular radio

https://easyeda.com/ae3k/softrock-filter

The spice simulation works, except I would like the baseline to be 0dB instead of -6dB.  When I do this in
the desktop version of LTSPICE, the voltage source has this form:

V1 N001 0 SINE(0 1 14000k) AC 2

The AC 2 part is what makes the baseline be 0 dB instead of -6 dB, as I understand it.

Anyway, the line that seems to get sent by EasyEDA to LTSPICE says AC 1 0, as follows:

V1 R1_1 GND SIN(0 1 14MEG 10M) AC 1 0

If I edit the line in the schematic to end with AC 2 0 instead, EasyEDA still appends AC 1 0,
which yields

V1 R1_1 GND SIN(0 1 14MEG 10M) AC 2 0 AC 1 0

and the net effect is that there is no change.

So I have two questions.  My main question is how to get EasyEDA to send the particular line I
want to LTSPICE?  For my schematic in EasyEDA, that would be

V1 R1_1 GND SIN(0 1 14MEG 10M) AC 2 0

And I guess I am also open to suggestions about how to finagle the plot in EasyEDA to change
the baseline in other ways.  More generally, I can do lots of customization in LTSPICE but in
the EasyEDA interface to it, what comes back seems fixed.

Thank you.

PS: I noticed also that the resulting plot is logarithmic on the frequency axis, but I specified
linear in the control-j dialog (and this is also seen in the .ac directive).  Should it not be linear
in the frequency scale in the plot?

#Bug Reports#
Bug Reports
EasyEDA for Linux segfault before starting

Fresh installed, till now I've only used the browser version.
This is on Ubuntu 19.10

andre@loke:/opt/easyeda$ gdb ./easyeda
GNU gdb (Ubuntu 8.3-0ubuntu1) 8.3
Copyright (C) 2019 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "x86_64-linux-gnu".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
.
Find the GDB manual and other documentation resources online at:
    .

For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./easyeda...
(No debugging symbols found in ./easyeda)
(gdb) r
Starting program: /opt/easyeda/easyeda
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".

Program received signal SIGSEGV, Segmentation fault.
0x0000000000dbf060 in ?? ()
0x0000000000dbf060 in ?? ()
(gdb) bt

0  0x0000000000dbf060 in  ()

1  0x00007ffff7d81072 in node::http2::Http2Session::Callbacks::Callbacks(bool) () at /opt/easyeda/libnode.so

2  0x00007ffff7d81135 in  () at /opt/easyeda/libnode.so

3  0x00007ffff7fe102a in call_init

    (l=, argc=argc@entry=1, argv=argv@entry=0x7fffffffdda8, env=env@entry=0x7fffffffddb8)
    at dl-init.c:72

4  0x00007ffff7fe1131 in call_init (env=0x7fffffffddb8, argv=0x7fffffffdda8, argc=1, l=)

    at dl-init.c:30
#5  0x00007ffff7fe1131 in _dl_init (main_map=0x7ffff7ffe190\, argc=1\, argv=0x7fffffffdda8\, env=0x7fffffffddb8)
    at dl-init.c:119
#6  0x00007ffff7fd113a in _dl_start_user () at /lib64/ld-linux-x86-64.so.2

7  0x0000000000000001 in  ()

8  0x00007fffffffe134 in  ()

9  0x0000000000000000 in  ()

(gdb) q
A debugging session is active.

Inferior 1 [process 17266] will be killed.

Quit anyway? (y or n) y
andre@loke:/opt/easyeda$

#Bug Reports#
Bug Reports
Rather BAD EasyEDA + JLCPCB + SMT assembly experience

Please see files here:  https://drive.google.com/drive/folders/1k18Cu3OPY8_nzICmUbo6Om4ODnvjpDmi?usp=sharing

1: BOM list in EasyEDA looks good, most parts selected from LCSC
1-most components look good in BOM list.png
2: exported BOM refers to 0603 packs as 0603'    (correcting that does not fix step 3)
3: the uploaded BOM fail to find the parts...
 3-Assembly fail to find the components.png

So I needed to choose all missing parts over again - the components I got to choose among, had wrong packages, and did not show the value in any place but the part number (for those who can decode it)

Once that is completed, and everything thing is put into the "shopping cart"  - one proceeds to payment.
Should one, at any point, try to go back before paying, (to check/verify how many PCB's or SMT assemblies were selected, then BANG - the cart is empty, and you need to start over again !)   Check my logs, I did it at least three times.

So I am not sure I got the right parts, and this way every test batch could be inconsistent with the previous batch. (as different parts may be selected)

#Bug Reports#
Bug Reports