I use easyeda and create a schematic,and then run. I get the netlist.
I save the netlist in local file called test.cir.Then I use ngspice to run test.cir in command line, it result error.
the ngspice result is:
Circuit: new schematic
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000
Initial Transient Solution
Node Voltage
xvm1_1 0
+5v 0
vxa1#branch 9.52495e-047
No. of Data Rows : 1008
probe: no such command available in ngspice
Note: No ".plot", ".print", or ".fourier" lines; no simulations run
the netlist as following:
Untitled
XS1 XVM1_1 GND SPST_ON
VXA1 +5V GND 0v
D1 +5V GND LED
.param pi = 3.141593
.func LIMIT(x, y, z) {min(max(x, min(y, z)), max(z, y))}
.func PWR(x,a) {(MAX(ABS(x), 1e-313))*a}
.func PWRS(x,a) {sgn(x) PWR(x,a)}
.func stp(x) {u(x)}
.func log10(x) {ln(x)/ln(10)}
.func SQRT(x) {(MAX(x, 1e-313))*0.5}
.func INT(x) {sgn(x)floor(ABS(x))}
.func URAMP(x) {max(x,0)}
.func POW(x,a)
-
{(((a-(int(a)))==0)||(sgn(x)>=0))( max(exp(ln(uramp(x))a),0) +
-
(2(0.5-ABS((int(a))-2int(a/2))))max(exp(ln(uramp(-1x))*a),0) )}
-
a res with very small value
.subckt SPST_ON 1 2
r 1 2 2u
.ENDS
.MODEL LED D
- IS=661.43E-24
- N=1.6455
- RS=4.8592
.control
tran 1u 1m 0
probe V(XVM1_1)-V(+5V) I(VXA1)
quit
.endc
.END
my project address is https://easyeda.com/editor#id=Fr0YI4cWi
#General Discuss#Greetings,
I'm trying to make a project or even save a PCB design and it simply doesn't do anything even though I'm logged in.
here is a video of the sample to see if anyone can help me with this
https://youtu.be/Mqpe4TksW1k
I've tried refreshing the browser with F5, tried it in chrome or firefox and doesn't work.
Any ideas?
btw I'm on windows 7
thanks
Best regards
Gregorio
Hi. I've never done PCB layout before. I was using a user-defined representation of the tlc5916 (http://www.ti.com.cn/cn/lit/ds/symlink/tlc5916.pdf) when I noticed the package name was something I couldn't find online - SOIC16N. When I changed it to the general package, SOIC-16, I noticed that the dimensions were completely different. According to the grid size, the SOIC-16 is slightly more than 0.4 inches long and 0.3 inches wide. But this doesn't correspond with the specification found here. I've attached an image. Also, is there a way to see the actual measurements of a package on the layout screen instead of eyeballing it with the grid? Thanks!
#PCB#Due to some cache issues, EasyEDA editor page may stop at an old version and cannot update to new version by common reload methods (Ctrl+R, Ctrl+F5, or click the reload button on browser), we can manually clear browser offline application cache to fix it.
Clear offline cache in Chrome:
- Close all easyeda editor pages
- Press
Ctrl+Shift+Deleteto remove cached files. - Enter appcache page: chrome://appcache-internals/ and find
easyeda.comitems, then clickRemove Item - Re-open easyeda editor page
Clear offline cache in Firefox:
- Close all easyeda editor pages
- Press
Ctrl+Shift+Deleteto remove cached files. - Enter advanced preference page: about:preferences#advanced, switch to
Networktab, findOffline Web Content and User Data, selecthttps://easyeda.comand clickRemove... - Re-open easyeda editor page
See which version I'm using:
#Skill#I can find no errors with this simple circuit yet I'm getting a simulation results are too large error. I have simmed 5 other circuits before this without errors. I seem to only be having errors with circuits using the 74HC11 and the 74HC08 models. Can someone take a look at this and tell me what's wrong?
https://easyeda.com/editor#,,,,id=rUusqMKjF
Thanks.
#Simulation#I'm not all that new to electronics, but I am new to Spice simulation. Here and there, I get errors from the simulator that say, "no DC value," and refer to a signal generator. The project I am working on now, which is based on a great paper written by John Caldwell, and published by TI, is a pre-amplifier for an electret microphone. Caldwell's paper shows how to simulate an electret with a DC power supply, an AC source, and a voltage-to-current converter. When I simulate his, uh, simulation, it works perfectly. However, when I add the rest of his pre-amplifier circuit, I get the "no DC value" error. This happens even if the pre-amplifier circuitry isn't connected (other than by a common ground) to the electret circuitry. I don't understand that at all.
Here's the project link:
https://easyeda.com/stevensrmiller/Electret_Simulator-gewqI0hbt
And here's the simulation report:
Circuit: untitled
Reducing trtol to 1 for xspice 'A' devices
Doing analysis at TEMP = 27.000000 and TNOM = 27.000000
Warning: vg2: no DC value, transient time 0 value used
Initial Transient Solution
--------------------------
Node Voltage
---- -------
xu1.11 -nan
xu1.12 -nan
xu1.6 nan
xu1.7 -nan
c2_2 -nan
xu1.53 -2.6
xu1.54 11.6
xu1.90 -nan
xu1.91 25
xu1.92 -25
vcc 9
xu1.99 4.5
xu1.10 nan
c2_1 -nan
xu1.13 nan
r5_1 -nan
xu1.14 nan
xu1.9 0
xu1.8 -nan
v1_+ 62
vg2_2 62
c3_2 -nan
r3_2 -nan
volprobe1 -nan
h.xu1.hlim#branch nan
v.xu1.vlim#branch -nan
v1#branch 0
v3#branch -nan
vg2#branch 0
v.xu1.vln#branch nan
v.xu1.vlp#branch nan
v.xu1.ve#branch -nan
v.xu1.vc#branch -nan
v.xu1.vb#branch nan
a$poly$e.xu1.egnd#branch_1_0 -nan
**********************************************************************************
Timeout,
Your simulation results are too large! Try reducing the total simulation time (Stop Time - Start Time), increasing
the maximum time step, removing some of your probes or breaking your circuit into smaller simulatable blocks.
**********************************************************************************
I'd be very grateful if someone could help me understand and correct this. Thanks!
#Simulation#The following basic astable 555 cirucit, which should have a period of about 2 seconds and a duty cycle of around 58%, produces a noisy square wave for about 60 seconds and then finishes the last 40 seconds of the simulation at a constant voltage:
Basic Astable 555 Period=2s, Duty=58%
The not-that-great-looking waveform is:
Why is this not a pretty square wave? Why does it stop after 60 seconds?
#Simulation#