Please make adding vias and changing layers consistent for 2 and for multilayer PCBs with inner plane layers.

This Feature Request is about how connect a track on a top or bottom layer to an inner VCC or GND PLANE layer.

If the PCB has any number of layers but each layer is only defined to be for tracking then the procedure to insert a via to change layer as described in: 

https://docs.easyeda.com/en/PCB/Route/index.html#Some-Tips-about-Track

works fine.

The problem is that the simple procedure described in the link above as:

  1. Route track;
  2. Press a layer hotkey (T, B, 1, 2 etc.) to auto-insert a via;
  3. Continue to route on the new layer

cannot be used on a multi-layer PCB when a via is to be placed to connect a track to an inner plane layer that  is defined as a PLANE (such as VCC or GND).

The desired action for tracks to be routed to inner PLANE layers is:

  1. Route track;
  2. Press a layer hotkey (T, B, 1, 2 etc.) to auto-insert a via;
  3. End routing of that track

At the moment however, a short segment of track has to be routed from each top or bottom layer pad that must be connected to an inner PLANE layer. That track segment has to be ended and a via manually invoked using the V hotkey and then the via snapped onto the end of the short track segment.

Thus is very different from what is described in the Tutorial and is not intuitive:

https://docs.easyeda.com/en/PCB/Route/index.html#Some-Tips-about-Track

#Feature Requests#
Feature Requests
Struggling with modules

Hi guys,

I'm designing a pcb which should have 4 (later 8) exactly the same units on it, together with some other stuff.
To accomplish this I was thinking about using modules and this is what I did:

First I created a whole new project for it (https://easyeda.com/mijnmodelbaan/lightning_02_copy)
Then I created a schematic and a pcb from that schematic.
Routed a few tracks by hand, used the local autorouter for the majority of the tracks and after routing the last tracks by hand, I was finished.
Well, that is to say, after routing the last few tracks by hand and correcting the DRC errors it was finished.
Then I saved the schematic as a schematic module and the pcb as a pcb module and started a new project (https://easyeda.com/mijnmodelbaan/module_testing).

In this project I created 2 sheets and on both sheets I put the schematic modules I created earlier.
For the first one I used the letters 'QQ', for the second one I used 'AA'.
After doing this I noticed the components were all renamed with the chosen letters (QQ, AA) in front of the original names.
Screenshot 2020-11-09 172426.png
But of the Nets only a few were renamed, 16 of the 49, and the ones not renamed pointed to both sheets.
Screenshot 2020-11-09 172612.png  Screenshot 2020-11-09 214021.png
This is not what I expected.

I created an empty pcb (just to see what would happen) and put 2 pcb modules on it (the ones I created earlier).
Here the same problem arised: after importing the changes only 16 of the 49 Nets were ok.
Screenshot 2020-11-09 173628.png

Please let me know what I did wrong so I can solve this, preferably in a simple way.

Thanks for your time.

#Schematic#
Circuit Design
Unable to connect ratlines from repeated symbols

I created a symbol to repeat it multiple times on a schematic, as advised in the documentation (https://docs.easyeda.com/en/Schematic/Wiring-Tools/index.html). The pins of the symbol and of its footprint are properly matched together, thanks to the Footprint Manager. After converting the schematic to a PCB, ratlines appear between repeated elements, as expected from the schematic, but I am not able to connect them with a wire. When checking for design rules, I get the following error:

The clearance between two objects is less than the Design Rule Checking clearance which has different nets.

I assume the reason is that the symbol itself only consists of wires (tracks). But what would be the recommended way to repeat the same element on a board in this case?

This public project is a simple example with two repeated elements: https://easyeda.com/bencfd/first-project
The wire I am not able to draw in particular is the one I marked with a red arrow on the schematic.

I am grateful to any hint you can provide to me. Thank you!

#PCB#
Circuit Design