Image Import Resolution + Size issues

Hi,

I'm using Easy EDA online editor to create a PCB. During which I found some "issues" that I would like to report. What I'm trying to do is use silkscreen layer voids to expose the underlying soldermask to "draw" (negative space).

The issues were:

  • Import Image Screen: Shows wrong image size.
  • Import Image Screen: When adjusting one of the sizes (width, height) the other one doesnt quite match the original. Very small error tough.
  • Imported Image: The actual imported image size is different that the one claimed (and / or specified) at the Import Image Screen
  • Imported Image lost a lot of details, had to split one image into multiple to mantain the same level of detail

Some of these were already mentioned here

Specifically I'm doing a PCB Tree, with snowed portions where are "letters" written with silkscreen blanks (exposing the soldermask). To do so I created a draft in Inkscape.
(Hopefully no family member reads the forum, otherwise my xmas surprise is ruined haha).

objetivo.png

This board is approx 70 x 100 mm
Now, to accomplish this I created a layer that is the snowed portions with the letters cutted-off.

This is how I export the file through Inkscape, notice the image size is 2500x2764 px (70.6x78 mm).

easyeda_3.png

Exiftools info shows the same, note that Pixel Per Unit is 35443, so 2500x2764 is roughly 70.6 x 78

easyeda_4.png
When I import it into EasyEDA the first thing I notice is the Image Size is wrong, claiming to be an astounding 631x5 x 702.68 mm

easyeda_5.png
I corrected the height and notice then the width is not exactly the same... 70.10 vs 70.6 mm. About 0.5 mm which is not that bad...may be a rounding issue with an underlying lib.
But, as soon as the image gets imported as part of a layer...Its size changes

easyeda_7.png
Again...not a big difference. But it odds me the difference of the size between the import screen and what actually gets imported.

Furthermore, what I noticed is the image lost quite a bit of details. Notice on the top, the words arent that nice.

easyeda_8.png

I tried changing from PNG to SVG and the results were actually worse

easyeda_12.png

I also tried .DFX which did mantain all the original details... but since there is no way (that I could find) whitin EasyEDA to convert that to a filled layer.

What I found to work is actually import smaller sized images. Instead of trying to import the whole silkscreen layer at once, I splitted into multiple images, for example

easyeda_15.png
(the dimensions are once again wrong, it is actually ~70x14 mm).
This produced a crisp imported image

easyeda_16.png

By repeating the process I was able to create the silkscreen with the desired level of detail

easyeda_17.png

Regards!

#PCB#
Circuit Design
Guide to Panelization of Board for PCB Assembly

This guide is relevant if you want the following:

  • panelize a PCB design, and
  • have a ground plane (copper fill)
  • use SMT assembly at JLCPCB

It covers a shortcoming (unsuitable for ground plane (copper fill)) of https://docs.easyeda.com/en/PCB/Panelize/index.html#Panelize-by-Manually

I wrote this guide so I don't have to reinvent the wheel next time I need one. I have sucessfully used it and confirmed that the PCBs ordered with assembly work as I intended. However, I will not take any responsibility for the correctness of this guide. USE AT YOUR OWN RISK. Based on at least one EasyEDA hack/bug, so it may cease to work with newer versions. Tested on V6.3.43.

1. Fully design and finish your single board\, including DRC.
image.png
2. Clone PCB design to new file (named XY_Panelized) in same project.
image.png
3. Use the built-in "Panelize" function to initially panelize the board.
image.png
image.png
Note that only the outline is panelized. All the components and layout are not copied. Let's call the upper left board that has all the components and layout the "primary board".
4. Clone the primary board to all secondary boards. Select the complete primary board including outline.
image.png
image.png
6. Use Ctrl+Shitf+C to copy by reference point. Use the upper left corner as reference point. Make sure you hit the corner of the primary board outline exactly\, zoom in as needed.
image.png
7. Use Ctrl+Shift+V to paste by reference point. Again\, make sure that you hit the corner of the secondary board exactly.
image.png
8. If everything is done correctly\, all of the primary board including the copper area is copied. Note that since we enabled panelization *and* we also copied the outline of the primary board\, the panelization will be extended and look wrong. We will fix this later. (Copying outline in this step is *required* because otherwise the copper area will not copy correctly!)
image.png
9. Repeat as needed until all secondary boards are copied.
image.png
10. Now we can fix the panelized outline. For every secondary board\, select and delete the outline. (This will NOT delete/destroy the ground plane and is\, in essence\, why this guide works!)
image.png
11. Open the Panelize Dialog and set to "No Panelize". All of the purple lines should be removed except for the primary board outline. This will clean up the outline mess that we made.
image.png
12. Then re-enable panelization\, with the exact same settings as before.
image.png
13. You should now have a panelized board that a) includes all components and layout on all sub-boards b) includes the ground plane for all sub boards and c) has the correct outline for you panel\, including stamp holes. You can generate gerber files for the panel and upload to JLCPCB.

#PCB#
PCB