Trying to get my first schematic to run

So it is my first schematic and I'm trying to run it.

Here's the schematic:
https://easyeda.com/djays12/Tachometer_electronics-076dcb60fc8f48358604c85fbfbcc000

I've already replaced the NPN transistor (it used to be a BCW66G) for a generic model that can be read by spice.

Mainly the circuit is a frequency/voltage converter that will be used to convert a 0-267Hz square wave signal into a 0-1.6Vdc voltage. The output of the LM2907 is then boosted through a op amp and a transistor to be able to output enough current for the load (an electromagnet, that I replaced by a inductor in the circuit).

This circuit will be used to power a tachometer (the electromagnet is acting on the needle and fight again a return spring).

The message error I get is as follow:

Circuit: gooduntitled

Doing analysis at TEMP = 27.000000 and TNOM = 27.000000

Warning: v2: no DC value, transient time 0 value used Warning:
singular matrix: check nodes u1_2 and u1_2

Note: Starting dynamic gmin stepping Note: One successful gmin step
Note: One successful gmin step Note: One successful gmin step Note:
One successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Warning: singular
matrix: check nodes u1_2 and u1_2

Warning: Dynamic gmin stepping failed Note: Starting source stepping
Warning: singular matrix: check nodes u1_2 and u1_2

Note: One successful gmin step Note: One successful gmin step Note:
One successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful gmin step Note: One
successful gmin step Note: One successful source step Warning:
singular matrix: check nodes u1_2 and u1_2

Warning: singular matrix: check nodes u1_2 and u1_2

Warning: source stepping failed

DC solution failed -

Last Node Voltages

Node Last Voltage Previous Iter
---- ------------ ------------- xr2_2 0 0 r1_1 0 0 u1_1 0 0 v1_1 0 5.8766e-118 r1_2 0 0 u2_6 -1.52529e-103 -1.38638e-117 volprobe1 5.35177e-104 7.98716e-118 l1_1 5.35177e-104 0 u1_2 0 0 l1#branch 0 0 v1#branch 2.51539e-115 0 v2#branch 0 0

doAnalyses: iteration limit reached

op simulation(s) aborted Error(parse.c--checkvalid): volprobe1: no
such vector. ngspice-26 done

Anyone have an idea on what I did wrong?

#Simulation#
Circuit Design
What if the designers start giving the essential training of EDA?

Hello, I am a graphic design expert and I have been working in the designing industry for past seven years. I am here to propose an idea to the members of this community. As I said above, I am a graphic design expert and after all these years I have gained command over almost all major design channels, be it a logo design service, website design, mobile application UI, stationary, video animation, etc. In fact, I have also worked with several clients who were looking for tri-fold brochure and banner design. Anyways, let’s stick to the idea which I am going to propose here. As we all know, there are fresh grads and individuals who want to pursue their career in the design industry but due to the obliviousness of what to do in order to succeed in their career, they fail. However, I think we can lift them by giving them a hand with this as sharing is caring. Let’s say if you are an expert circuit designer or have a specialty in using EDA, you can share tutorials for training or live webinars and seminars to train users for how to use these tools, I am sure you will receive a positive feedback. I hope you guys would surely like my idea.

#General Discuss#
Others